ADIABATIC COOLING KIT & PRE-COOLING OF AIR COOLED CONDENSOR
Adiabatic cooling technology or “precooling” for air cooled chillers essentially reduces the temperature of the air passing across the cooling coils by spraying water into the incoming air stream.
TRUE ADIABATIC COOLING
True Energy Savers, Evaporative Cooling systems are Cost-Effective, Efficient, and controllable which are effective in reducing in energy consumption of large Air Conditioner chiller units for Industrial and commercial places.Adiabatic cooling of air is an indirect evaporative cooling process air flowing through a closed-loop is pre-cooled to the desired temperature. Water channeled through an adiabatic system is evaporated as required. The state change from liquid to gas results in an energy transfer in the form of heat
Following are the advantage when the AC condenser unit runs efficiently:
- Less energy consumption
- Releasing of fewer greenhouse gases
- Water savings
- Cost-saving and Economical as a result of less energy and water usage
OUR PRODUCTS
HIGH PRESSURE MISTING SYSTEM PUMPS
Misting pumps Supplier & manufacturer in India. The high pressure needed to force the water through the nozzle, creating fine water droplets in the smallest sizes of below 50 microns.
MIST & FOG NOZZLES
A fire-hose nozzle that discharges a fine spray of water or foam. So a nozzle that produces a mist at 5 bar pressure may well produce a fog spraying at 15 bar pressure.
MISTING SYSTEM FILTERS
Misting systems have filter systems help debris and impurities. These misting filters clean the water and remove unwanted particles. Best filter for misting system is Calcium Filters.
HIGH PRESSURE MISTING TUBE
Manufacturer, supplier and Exporters of High pressure misting tubes in India. Generally with beads between 15 microns and 50 microns in measure.
FITTINGS AND ACCESSORIES
Manufactures and supplies variety of misting system accessories and fittings that will solve any of your misting needs. We manufacture both brass and stainless steel misting fittings
benefits of adiabatic pre-cooling for your cooling system
- Save energy
- Lower peak power
- Increase your cooling capacity
- No heat stress
CASE STUDIES
Our technical support provides systematic reports on the performance of the Adiabatic Cooling system, efficiency and condenser condition control. Adiabatic Cooling provides technical support in all regions and continents we operate. We are experts in hybrid cooling technology combining adiabatic and mechanical cooling.
Greenhouse
Testing was conducted in July of 2021. After the installation of the Adiabatic Cooling system, the cooling equipment produced noticeably more cooling capacity:17% on average. Electricity consumption dropped to around 15%
on average. The return on investment (ROI) period of the Adiabatic Cooling system for this project is of only 21 months. Test results show that the intelligent adiabatic equipment Cooling TM increased chiller performance by, on average, 15% during 24 operational hours.
RTA office Commercial buildings
The chillers at RTA were fitted with customized Adiabatic Cooling equipment allowing them to operate at sustainable rates, even during heat season, and deliver optimum cooling output while consuming less electricity. After the installation of the intelligent adiabatic Cooling system on RTA’s cooling equipment electricity consumption dropped by 20.8%. The return on investment (ROI) period of the installed equipment is 36 months.
frequently asked questions
Adiabatic cooling of air is an indirect evaporative cooling process air flowing through a closed-loop is pre-cooled to the desired temperature. Water channeled through an adiabatic system is evaporated as required. The state change from liquid to gas results in an energy transfer in the form of heat.
A typical adiabatic cooling system pulls air from the external environment, reduces its temperature by evaporating water in its presence, and then feeds the cooled air to a heat exchanger. The thermal exchanger eliminates heat energy from the associated process/equipment and transfers it to the cool ambient air.
Adiabatic cooling reduces the temperature of the air entering the coil, facilitating improvement of equipment reliability and efficiency. Operating equipment outside design parameters may significantly reduce reliability and efficiency.
Adiabatic cooling can be used in chiller units replacing conventional water or air-cooled devices. Chiller systems based on adiabatic cooling may possess even greater cooling efficiency than conventional air-cooled or water-cooled devices depending on the external environment.
Yes it is a GREEN Product which improves Energy Efficiency Ration (EER) by 20%